What parts would be needed for a long trip?

[Iggy]

Trying to list what parts would be good to have other than the common ones. As in filters, belts, hoses and impellers.

More so for a Yanmar 6LY engine and a 6K northern lights genset.

For the genset I do have the mixing elbow
For the Yanmar a thermostat.

 

[psneeld]

Is this a far offshore "long trip" or a long coastal cruise with possibility of assistance, tow to reasonable sized port and decent package delivery?

 

[O C Diver]

It depends on the definition of a long trip. Some think a thousand miles is long, others would say ten thousand. I tended to view it in hours of engine time. Annually I did close to a thousand hours per year. Obviously I would carry everything to complete required book maintenance during the time period.

In addition, I had:

Starter
Alternator
Fuel pump
All fuel filters
Raw water pump
" " " impellers
All anodes
Fresh water pump
Belt tensioner
All idler pulleys
Serpentine belt
Thermostats and gaskets
Radiator cap
Antifreeze change
Any specialized engine hoses
Rescue tape

The tools and manuals to install the above.

Ted

 

[ranger58sb]

Trying to list what parts would be good to have other than the common ones. As in filters, belts, hoses and impellers.

More so for a Yanmar 6LY engine and a 6K northern lights genset.

For the genset I do have the mixing elbow
For the Yanmar a thermostat.

How far will you ever be from an Amazon delivery point, or from a FedEx/UPS delivery location?

What systems on the boat are approaching obsolescence? Or what parts, if any, are already scarce in the supply chain?

-Chris

 

[ranger58sb]

How far will you ever be from an Amazon delivery point, or from a FedEx/UPS delivery location?

What systems on the boat are approaching obsolescence? Or what parts, if any, are already scarce in the supply chain?

-Chris

 

[JackConnick]

Lots of filters; fuel, oil, air for each engine and generator. Plenty of oil to do at least one change.
Tools
Replacement pumps and some hoses for all systems
Generator: A set of oil, temp sensors. Relays (4), belt, impellers. Install the new s/s elbow. Gaskets for rocker cover.
Fuses for everything on board.

Jack

 

[SteveK]

When the single or twin discussion comes up again, I must remember spare parts, as in a complete second engine to keep one going.

 

[Cold Duck]

This is pretty much impossible to answer without more info. The short answer is as much as you can comfortably carry on the boat. A 70fter can carry a lot more spares than say a 40fter. I lost an inverter in Geeorgetown, Bahamas. Was able to purchase online and have shipped free to a small airline in Florida who then shipped it to Geogetown. A short taxi ride to airport and I had new inverter installed 48 hours after failure. So where you are cruising will make a difference. The world is a much smaller place than it used to be.

 

[rslifkin]

I lost an inverter in Geeorgetown, Bahamas. Was able to purchase online and have shipped free to a small airline in Florida who then shipped it to Geogetown. A short taxi ride to airport and I had new inverter installed 48 hours after failure. So where you are cruising will make a difference. The world is a much smaller place than it used to be.

That's a big thing. I look at spares I need to carry as being the things I might need on short notice and are either easy to carry, or hard to get on short notice. And then there's also the question of what things will allow me to resolve a problem myself vs what things will still require some kind of outside assistance.

Cruising grounds factor in, as well as specific parts for a given boat. For example, I've learned that I need to carry spare starters, as mine aren't something that's regularly stocked in stores, so I can't just get one anywhere like you can for some engines. Mine are a common starter, but not the most common version of it, so they typically have to be ordered which takes a couple of days.

 

[TJM]

Along with the spare parts list, you would need all of the tools to replace or repair those items. Pry bars, liquid wrench, heat gun for hose removal. Get practice at fuel filter changes and bleeding the lines. I have set of color coded (painted with nail polish) wrenches that correspond to the vent plugs when I need to bleed my fuel system. Plugs are painted the same color as each wrench.