Search results

fuel tank repair JB Weld makes 2 products designed to repair fuel tanks from the outside. I have used them both, successfully. Bob

BTP pump with built-in pressure sensor. Set ther correct pressure. Connect to battery. Fit hose to dink or raft. Press the ON button. Thats it. When the set pressure is met, unit shuts off. Deflates just as easy. Slightly used- Excellent condition. Includes all original accessories plus 20'...

Group 31 batt I've purchased numerous Exide group 31 deep cycle batteries ove the years. THYey have removeable caps. Last purchase was 6 months ago at Batteries Unlimited. Bob

tank leak J B Weld makes 2 products for steel tank repairs. Tank weld is a 1 x3 inch strip of fibreglass with a pack of hardner that, when mixed getss hot instantly and dries in about 15 seconds. Hard to use, but very affective. THey also have a putty stick that works well. THey aere both...

On an alt with an external regulator, the regulator is programmed to delay charging for a period of time to give the engine time to warm up. 3-4 min sounds about right. Bob

Holding tank filter I had the odor problem several years ago. After some thought, I crated a vent filter from pvc tubing using charcoal filter material from an aquarium supply co. lasts quite a while. When the odor starts to build, I just change the charcoal. Bob

Fuel tank repair I've successfully used 2 products from JB Weld to repair a visible small leak on a steel tank. #8217 is a putty stick that you knead together & press or clamp on the affected area for about 15 min. #2110 is a piece of fibreglass tape and mixible packets of of epoxy that heat...

Price reduced!!! ok...$75.00

BTP122 Manometer 12V DC inflator. Tired of pumping up your inflatable by hand or foot. . This is the answer. Plug into 12v outlet, fit to inflatable inlet, set the gauge to proper pressure, touch the switch and stand back. In minutes the inflatation is complete and the pump shuts down...

Walker Bay Genesis Odyssey Model 270HP. Hypalon Construction with air floor. Length 8' 10". Tubes have never been patched. The air floor has a slight leak. Otherwise in great shape. Includes oars, hard seat, seat cushion, foot pump, anchor with rode and storage cover. FL title and...

Sold!!!

Light use as auxilary on inflatable. Includes: Custom test stand, lifting harness, spare prop (new), spare inpeller (new), manual, Clymer shop manual, gas can to fill internal tank, extra oil & cover. Recently serviced-lower unit oil replaced, new zinc, new water pump and new carburator. Pick-up...

replace the fuel filters, both of them.Bob

check the top of the tank. Alot of older boats have sight gauges that work magnetically with the tank float. Other wise-fill the tank, measure with a stick, run it for 10 hrs and measure again and so-on

thru-hull replacement try this... 1-1/4 dowel approx 8-10" long 1-2" disc of hypalong or heavy vinyl 1-small screw and small flat washer Punch a hole in the middle of the 2" disc. Push the screw with the washer thru the disc and screw into end of the dowel. Push the disc thru the valve until...

spanner socket for paragon The socket I used for a velvet drive was 1 11/16"... might be the same size. Bob

Perkins 4-108 parts I have an extra Lucas starter for the 4-108 with the solenoid and drive attached is good working order. Located in Pompano Beach. Bob

Band-aids!!!!

propane refil valve you can get them on aliexpress.com for about $2.00

Never used, still bright yellow 1-Marinco splitter 1 50 amp male, 2-30amp female 125/250 v $105.00 1-30amp, 50'cord $35.00. Location S. Fl. Bob

I have 2 heat exchangers for the lowline style. Length -12", dia-3". This is the style that fits across the back of the engine below the oil filter. Both clean, have zinc fitting and end caps. $85.00 ea. Can ship USPS priority (lge Ctn) for $20.00. Want a photo? PM me Also have a Lucas starter...

replacing damper plate I am 73 years old and and am just finishing up replacing the damper plate on a velvet drive matched to a 4-108 in a sailboat. If you trawler guys think it s tough, try it in a sailboat. The tight work space is the problem-other wise just a routine job-keeps me flexible...

velvet drive Interesting thread...If a pressure gauge is installed, what is acceptable pressure for a transmission that is operating properly? What does HP mean? What dfoes low pressure mean? Bob

Explorer Chartbooks Exumas & Ragged Islands, 5th edition...Brand new Near Bahamas, 3rd edition...very good condition Dodges "Guide to Abaco"-good condition. $95.00 for the set...I'll pay postage To US Location (lower 48). Sold as a set only.

Smelly head If the smell is coming from the holding tank, the hoses are good. no clamps are loose and the vent is clear...try a vent filter. They are avail to purchase. ..about $80. I made one using a piece of pvc pipe and activated charcoal...cost about $15. Requires refilling once a year Bob