Search results

Was in echo bay last Tuesday and Wednesday , averaged 40 boats in there but there's plenty of room. wind picked up every night but no problems.

Webbing attached is like 40ft and is stamped 2500lb

Thanks I thought it had something to do with climbing or in this case falling and had on business on a boat

I think the previous owner used it for mooring. its big, no manufacture name on it. I suspect its not for marine use, maybe climbing gear I don't know. would like to get some load spec's.

Ok new carb kit and I it looked like I found the problem. the float jet did have a swollen tip compared to the new one. installed kit and it ran great until it warmed up ,then same problem. So fuel must not be the problem I turn to electrical. I had originally clean and gapped the plug, but put...

Good to know I just found a jet that is behind a brass plug, I'm sure the plug is for emitions control. But when removed I found yet another passage that seemed to have gunk in it. I hate the factory set jets, they run when you buy them but after some hours they start running bad with now way...

I just started using the Eartec Simultalk 24G 2-way system and so far I like them. The price is not to out there and they work as billed. Its much better then trying to yell over the boats motor and wind. Makes for a more calm docking.

Great advise, got some parts coming. Ill let every one know how it go's.

There are only fixed jets and adjusted the float. I have a carb kit coming with new gaskets and a fuel pump. I will check into the plug, it did not cross my mind that it could be a plug problem. I will get a new hose and primer as well. that will make the fuel system all new!

Just let my 21 Bayrunner go to a good new owner. Had a lot off good times in her and will miss her. But I no there will be more good times to come in my new boat. that's the way it go's

Having problem with my Tohatsu 5hp 4 stroke . It came with Athena for her dingy, from day 1 it ran great until you give it full throttle then it cuts out and dies. Then it will start up and run at low rpm's until you give it to much throttle. So I'm thinking lack of fuel, so I went there the...

Wow that is a 41 roughwater. same layout with just minor changes. they should have went with the pilothouse. don't like the only place to pilot the boat from is out in the elements.

Go to the roughwater form, They have been talking but don't think anything is in stone.

Ok here's one for you, a super yacht sub Tour the world's most luxurious submarine superyacht | Fox News

That's for the input I will look into all and get back what I find Thanks

Looking for a good place to buy parts for my Perkins 6.354 in the Seattle/Tacoma area closer to Tacoma would be best. I found Tacoma Diesel ,looks good but I don't know if that's the best place to go? Any input would be appreciated. Spending the 1st 3 weeks in may working on the boat in Bremerton.

We use the Weaver davits and love them, doesn't get any simpler. when were under way we pull the dingy all the way up against the transom. at the dock back her off a couple feet and you have full use of the swim platform. my wife loves it because with the dingy there she does not have the...

I'm looking to install a heating system on my boat. I looked this over and I like it . How many registers is it able to handle?

Hi Mickey I bought a 1977 41 roughwater Atena last October and starting to refurbish her as will. Good luck and don't hesitate to ask questions, someone here will have the answer

Diesel was $1.77 a gallon

Thanks every one great input. I thought I would be ok but wanted to bounce it of everyone.

No children just adults, short ride on protected waters.

I have a family outing come up on the boat and don't want to leave any one out, but am concerned about over loading the boat. The boat is 41 ft x 13ft single diesel and looking at 12 people on board. What do you think.

attention roughwater owners look at the roughwater form there's a lady in Pittsburg CA that says she has a long lost 58 for sale needs work?

Thanks for the input I found a calculator looks like 3 to 4 gallons for 2 coats and a 3rd at the water line.