Search results

Check out Marcel, Sensored life units. Worked great for me for years, no false alarms, and very economical!

Spread has been gifted . Thanks everyone!

We have sold boat and have an original master queen bedspread in excellent condition with matching shams. Just pay shipping!

Mine had a little corrosion, so I sanded and painted it, brushed on and then he applied vinyl wrap. Came out great. I try to find pictures as I sold boat one year ago.

We had a professional vinyl wrap the doors and turned out great. 3 hours and cheap compared to painting!!

Take a look at sensored life , by Marvell Works great for temperature, water intrusion, and electricity. Had it 3 years, and cheap.

abc.sc@mvtel.net Thank you so much, my mainship is being serviced for cutless and dripless and so far rudders may also need replacing. Could you also tell me what they charged to make your new one?

Hi saiorskip: could you possibly give me the name of your upholstery guy, as I have tried to explain the process to several vinyl companies and I am not getting any favorable response. Thanks Alan

Mike : I have a 2004 ms 400 twin 240 hp and have a rudder that has quite a bit of corrosion and was wondering if you found a rudder or did you have one manufactured? Any additional info would be appreciated.

Congratulations to both of you! What is the estimated delivery date?

On my mainship 400 the co2 sensor chirped when 12 volt battery was low voltage. Got a new battery and it quit chirping and went to green, but did install all new co2 detectors, as they were 2005 also. Hope this helps

Try calling P&D marine , orange beach , alabama. 251-981-6431 . They have helped me in past on such things.

Pictures and drawings of stair lift Hello all: Hope this works! A sincere appreciation to all who helped me figure how to upload photos. You are the best. Many thanks for all the knowledge on the mainship 400. Fun boat to restore?

gas assist stair project I cannot get pics to download, so I will try to write and explanation. If this is not sufficient I will keep trying but so far 1 hour in and no download. I cut a 4 inch by 1and 3/4 inch board for the bottom gas assist to attach, it is located 32 inches off the floor...

Soo proud for you and your family! Have fun and smooth waters always��

Gary: I will take pics and get measurements next week when I get to boat and email you and also put on forum, as there is some interest in project from members.

Thank y’all, bet that is my problem also,have been hitting with flip/ flop! Maybe you found the cure for me?

167 degrees if on the 75 degree Celsius mark.

Looks like it is below the 175 degree mark.

Stairway lift Hi Alan here: I just put a gas lift on and love it. Moved the microwave down there for more storage in the cabinet. Used wholesale marine , 60 lb lift 20” , works well , but does not hold up right completely as still use bar but assists well . S-d-321486-1 and s-d 321583-1 on...

Try putting a copper wire in the strainer, it will corrode first! Worked for mine.

Another mainship 400 question. Has anyone reworked the vinyl liner on the walls with wood or a composite? If so, would like to know how it was attached and the complexity of the project. I have not been able to find a upholstery person to redo it in the original vinyl. Thanks

Have a 2004 mainship 400 and wondering if anyone know if I can drill out the original vent of holding line from the outside. I can see two small holes at bottom half of vent with screen, but can’t seem to get them removed. Can I just drill, possibly a 3/4 “ hole in center to open it up? I plan...

Thanks, I just replaced both mine with Stainless also, it was a pain in the butt. Anything else you had problems with?

Cleaning soot from engine room Just had same happen to me on Yanmar 240. Cleaned engines and er with bucket of water , shot of dawn dish washing detergent, and roll off. Roll off is great , I order by gallon. Good luck, lots of rubbing, but er looks new now!?